Simco Coatings Inc.
211 Gunther Ln.
Belle Chasse, LA 70037
Office: 504.393.9455
Toll-Free: 866.95.SIMCO
Fax: 504.433.1406
For more information or purchase request
Email: sales@simcocoatings.com
Legal/Privacy Info.
|
|
SIMLUX-800 MARINE ENAMEL
General Properties:
SIMLUX-800 is a gloss alkyd finish coating possessing good color and gloss retention for interior and exterior applications. Designed for application over alkyd primers.
Principle Properties and Uses:
|
- Particularly suitable as a finish coat for bootop, topside, deck and deck equipment. |
|
|
- A quick drying, hard, tough water resistant coating. |
|
|
- Can be applied over intact existing conventional systems and over suitable primers. |
|
|
- Good adhesion properties in wet and dry exposure conditions |
|
Technical Data
| Generic Type: |
High gloss alkyd finish. |
|
| Color and Finish: |
Consult Color Card ; Gloss |
|
| Application Temperature |
Normal |
Minimum |
Maximum |
|
| Ambient Air: |
60-100º F |
50º F |
110º F |
|
| Material: |
50-90º F |
40º F |
110º F |
|
| Surface: |
50-90º F |
35º F |
120º F |
|
| Humidity: |
10-80% |
0% |
85% |
|
| Temperature Resistance: |
|
|
| Continous: |
175º F |
|
| Occassional: |
225º F |
|
| Percent Solids by Volume: |
40-45 depending on color |
|
| Theoretical Coverage: |
642 sq. ft. per gal @ 1 mil |
|
| Flash Point: |
50º F |
|
| Recommended DFT: |
|
|
| Wet: |
4.0 - 5.0 mils |
|
| Dry: |
1.0 - 2.0 mils |
|
| Drying Time: |
at 50º F |
at 70º F |
at 90º F |
|
| To touch: |
4 hrs. |
2 hrs. |
45 min. |
|
| To handle: |
6 hrs. |
3 hrs. |
2 hrs. |
|
| To recoat: |
24 hrs. |
8 hrs. |
4 hrs. |
|
| Non-Immersion: |
72 hrs. |
24 hrs. |
18 hrs. |
|
| Immersion |
- |
- |
- |
|
| Shelf Life: |
18 months |
|
| Recommended Thinner: |
T-1 Thinner for Enamel |
|
Surface Preparation:
All surfaces must be clean, dry and free from all loose rust, scale, paint or oil. For best result abrasive blast SSPC-SP6 commercial.
Application Data:
Brush, roller, spray.
Safety Precautions:
(A) Use normal precautions such as gloves, facemasks.
(B) Adequate ventilation must be maintained.
(C) Explosion proof lights & electrical equipment.
(D) Non-Sparking shoes & tools for workers in area.
(E) This product contains flammable materials. Forbid all flames, smoking and welding in work area.
(F) Avoid breathing of vapor, contact with skin or eyes. If product comes in contact with skin or eyes, wash thoroughly with water and obtain medical attention.
Non-Warranty:
The technical data listed herein has been compiled for your convenience and guidance, and is based upon our experience and knowledge. However, since we have no control over the use of this information of this product, no warranty expressed or implied, is intended or given. Simco Coatings, Inc. assumes no responsibility whatsoever for coverage, performance, or any other damages, including injuries resulting from use of this information or of products recommended herein.
|
 |
Copyright © 2001-2006 Simco Coatings Inc. All rights reserved.
|
|
